Water Features

Building a Garden Stream: Liner, Pump and Layout

Plan and build a garden stream with the right slope, EPDM liner, pump flow and reservoir size, so the water runs over the stones and stays in the feature.

On this page
  1. Choose pond-fed or pondless
  2. Plan the layout
  3. Check the grade and drops
  4. Dig the channel
  5. Dig the reservoir
  6. Choose and fit the liner
  7. Size the pump
  8. Build the streambed and falls
  9. Rocks, gravel and planting
  10. Start up and tune
  11. Costs and time
  12. Maintenance
  13. Safety

A garden stream is a channel with a gentle drop, a liner underneath, a pump that carries water back to the top, and rock to hide the liner. Get the slope, the liner size and the pump flow right, and the water runs over the stones and stays in the stream. Get them wrong, and the water either drains away or sits still.

Choose pond-fed or pondless

A pond-fed stream empties into a visible pond. The pond holds the pump and collects the water. A pondless stream empties into a hidden reservoir of gravel or matrix blocks, with no open water. Pondless is simpler to care for, but it cannot hold fish. The rest of this guide applies to both.

Plan the layout

Most streams follow the same plan. Water starts at a header pool or biofalls at the top, runs down a winding channel, and drains into a bottom pond or reservoir where the pump sits.

Use a garden hose or spray paint to mark the route before you dig. Keep the top, the channel and the bottom reservoir in view of each other so you can check the flow as you work.

Check the grade and drops

A gentle slope is usually enough. Aim for about 1 to 3 inches of drop per 10 feet of stream.

  • Gentle grades look more natural and sound quieter.
  • Steeper grades need steps or small falls, which add sound. On a steep site, see building on a sloped garden.
  • Check dams and pools slow the water and let the stream hold some water when the pump stops.

Dig the channel

Dig a channel about 1 to 3 feet wide and 6 to 10 inches deep. That depth holds about 3 to 6 inches of water once the liner and underlayment are in.

Carve the channel so it slopes gently toward the bottom. Remove sharp stones, roots and glass. Compact the soil in layers so the bed does not sink or sag later.

Dig the reservoir

The bottom reservoir holds the pump and collects the water that drains back when the pump stops. It must be big enough to take all of that drainback, plus a margin. If it is too small, the pump runs dry when the stream empties into it.

A reservoir of about 18 to 24 inches deep is a common starting point for a pond or basin. Make the walls stable, and keep the bottom flat.

Choose and fit the liner

Use 45-mil EPDM over a geotextile underlayment. EPDM is fish- and plant-safe and often lasts 20 years or more. PVC liners cost less but wear out sooner.

To size the liner for a channel, use this formula: liner width = channel width + 2 × maximum depth + about 2 feet of overlap. The liner runs the full length of the channel, with overlap at each end.

  • Lay the underlayment first, then the liner over it.
  • Join sheets shingle-style. Put the upstream piece over the downstream piece by about 12 inches. Seal the seam with EPDM seam tape.
  • Keep the edges high. Keep both edges level and above the water line. Low edges cause most water loss.
  • Cover all the liner. Exposed liner degrades in sunlight, so cover every edge with stone or soil.

Size the pump

The pump has to deliver enough flow at the height the water must reach.

  • Flow. For visible flow, plan on about 100 to 150 gallons per hour (GPH) per inch of stream width. Figures vary by design.
  • Head. Total head is the vertical rise from the pump to the top of the stream, plus about 1 foot for every 10 feet of pipe to cover friction.
  • Pipe. Use 1.5 to 2-inch flexible PVC, buried beside the stream.
  • Valve. Put a ball valve near the pump outlet. It lets you fine-tune the flow and the sound.

Pumps are rated at zero head, so flow drops as the lift rises. Read the pump curve at your calculated head before you buy. Do not rely on the GPH on the box.

Build the streambed and falls

  1. Set the drops. At each waterfall, dig down to the depth of the drop, or build up the falls if you are working above grade.
  2. Lay the liner with slack. Leave a little slack at the base of each waterfall. Placing heavy boulders can stretch or rip a tight liner.
  3. Set the spill stones. Place flat stones at the lip of each drop. Use black waterfall foam under and around them so the water goes over the lip, not under it.
  4. Protect the liner under heavy stones. Add a small piece of liner under any heavy stone at the edge.
  5. Fill the gaps. Use foam and stones to close every gap that water could escape through.

Rocks, gravel and planting

  • Large stones on the edges. Place them at turns, drops and the edges of the falls.
  • Washed gravel on the bed. Spread about 1 to 2 inches of gravel to cover the liner and make the stream look natural.
  • Planting pockets. Leave gaps along the edges for marginal plants and ferns. They soften the edge and help the feature blend into the garden.

Start up and tune

  1. Fill the reservoir and upper pool until the water flows naturally down the stream.
  2. Turn on the pump and watch the flow. Listen for air in the lines.
  3. Adjust the ball valve to set the flow rate and sound.
  4. Walk the length of the stream and check every stone joint and liner edge for leaks.
  5. Adjust any stones that make the water run around instead of over them.

Costs and time

Materials for a 20 to 30 foot stream often add up to the low thousands of dollars, depending on the liner, stone and pump. Costs vary widely by region. A modest DIY build can take several days of work, plus waiting for stone and liner delivery. For the broader cost picture, see how expensive water features are.

Maintenance

  • Monthly: Clear leaves from the strainer, skimmer and pump intake. Check the pump inlet for clogs.
  • Quarterly: Rinse the gravel and smaller stones with a hose to lift sediment.
  • Spring: Top up the water lost to evaporation, restart the pump, rebalance the flow and trim plants.
  • Fall: Clear leaves, trim plants and winterize the pump, or switch it off and store it.

Safety

  • Call 811 in the US, or your local locate service, a few days before you dig.
  • Use a GFCI-protected outlet for the pump.
  • Move heavy boulders with proper technique or equipment. They can crush fingers or toes.
  • Keep an eye on children. Shallow moving water can still be a risk.

For the parts of a waterfall and the flow math in more detail, see pond waterfalls and pondless water features. For pump choice in smaller ponds, see fountains for small ponds.

The complete guide to water features

Simple Backyard Water Features: Types and Ideas
Read the guide

Keep exploring

Guides from other topics

All topics →