Pumps and Filters

Pond Filter Installation: Media, Matting and Covers

How to install a pond filter: media order, Japanese matting, moving-bed media, gravity versus pressurized bases, and a vented cover that blocks sunlight.

On this page
  1. Choose the right filter type
  2. Media order
  3. Japanese matting
  4. Moving-bed and static biological media
  5. Plumbing and UV placement
  6. Start-up
  7. Covers for pond filters
  8. Common mistakes
  9. Safety

Install a pond filter with mechanical media first, biological media second and fine polishing media last. Set it on a firm, level base, choose the filter type that suits your pond, and fit a vented cover that blocks sunlight.

Choose the right filter type

A gravity (box) filter sits with its top above the pond’s water line and returns water by gravity. Its outlet pipe should be larger than its inlet, and it must sit level.

A pressurized filter is sealed and can be partly buried, with its lid at ground level. It can push water uphill. Leave the cleaning handle and outlets reachable, so you can clean it without digging it out.

Whichever type you choose, give it a compacted, level base of sand or a paving slab. Water weighs about 8.3 pounds per US gallon (about 1 kg per liter), so a full filter is heavy and needs firm support.

Media order

Load the filter in stages, coarse to fine:

  1. Mechanical media such as brushes, coarse foam and matting, to trap debris.
  2. Biological media such as moving-bed or static media, where bacteria settle.
  3. Fine polishing foam or floss, last, to catch what remains.

More fine media is not better. Dense fine media clogs quickly, and water then channels around it instead of through it.

Japanese matting

Japanese matting is made of rigid, open polyester filament sheets, commonly about 1.5 inches (38 mm) thick. It works in upflow and downflow chambers, waterfall boxes and skimmers.

  • It clogs slowly and can last for years. It isn’t permanent, though. Rinse it regularly and replace it once it no longer cleans or drains well.
  • Clean it by hosing it down or dunking it in pond water.
  • Density is graded by color, but the color codes vary by brand. Check the maker’s chart before you buy, and don’t assume one code system applies to every brand.

Moving-bed and static biological media

  • Moving-bed (K1-style) media should fill about 50 to 60 percent of the chamber. Aerate the chamber so the media tumbles and stays clean.
  • Static media such as ceramic rings, bio balls and lava rock also work. Lava rock traps dirt, so keep it in a mesh bag where you can lift it out to rinse.
  • Loose media is easier to handle and clean when it is bagged in mesh.
  • Rinse media in pond water. Never use chlorinated tap water, because chlorine and chloramine kill the bacteria.

Plumbing and UV placement

The usual order is pump, then UV, then mechanical stage, then biological stage, then return. Fit the UV before the filter or between stages, following the maker’s instructions.

  • Use hose tails that match the pump outlet.
  • Use stainless steel clamps, and fit a union or valve so the filter can be removed for cleaning.
  • Check the UV’s power supply. Put the UV and the pump on a GFCI or RCD.

Start-up

Bacteria take about 4 to 6 weeks to establish in new media, and they slow sharply below about 50°F (10°C). Add fish only once the filter has cycled, and test ammonia and nitrite during the first weeks. Adding fish too early is one of the most common causes of losses in new ponds, as the common causes of fish death in ponds explains.

Later, replace media in stages. Swapping out all the media at once restarts the cycle, and your bacteria have to rebuild.

Covers for pond filters

A filter cover has three jobs: keep out sunlight, keep out debris and animals, and let heat and gases escape.

  • Block sunlight. Light reaching the media lets algae grow inside the filter box. Clear lids let in sunlight, so avoid them.
  • Stay UV-stable. Covers exposed to sun for years should be made of UV-resistant material.
  • Vent the cover. Vented covers let heat and gases escape. Keep leaves, pets and children out.
  • Choose a style that suits the site. Rock-style covers hide equipment well. Insulated options help in cold climates.
  • Keep access easy. The cover should lift off so you can reach the lid, handle or outlets when you need them.

Common mistakes

  • Clear lids. They let sunlight in and grow algae inside the filter.
  • Too much fine media. It clogs and channels water around the media.
  • Replacing everything at once. This restarts the bacterial cycle.
  • Scrubbing biological media spotless. Leave a film of bacteria on it.
  • Rinsing in tap water. Chlorine and chloramine kill the bacteria the filter depends on.

Safety

Put the UV and the pump on a GFCI or RCD, and keep electrics out of standing water. Never look directly at a lit UV-C lamp, because it can damage your eyes.

For sizing the pump and filter to your pond, see pond pump and filter setup. For upkeep of the media once the filter is running, see cleaning a pond filter. A skimmer can serve as the mechanical stage ahead of the filter, as described in pond skimmers.

The complete guide to pumps and filters

Pond Pump and Filter Setup: Sizing and Plumbing a Pond System
Read the guide

Keep exploring

Guides from other topics

All topics →