Water Features

Pond Waterfalls and Pondless Water Features

Compare pond waterfalls with pondless features, learn the parts and flow math, and get safe, realistic answers on building, cost, clear water and fish.

On this page
  1. What is a pondless water feature?
  2. Pond waterfall vs pondless
  3. Can I just build a pond in my backyard?
  4. The parts of a waterfall
  5. How the water flows: head, flow and pipe
  6. Building the falls, step by step
  7. Keeping pond water clear naturally
  8. Do fish like fountains in ponds?
  9. How much does a backyard waterfall cost?
  10. What are the three types of waterfalls?
  11. Safety

A waterfall is a fall of water over stone. The main design choice is where the water lands. A pond waterfall spills into an open pool, which can hold fish and plants. A pondless waterfall drains into a hidden reservoir under rock, so there is no open water. That makes it simpler to care for, but it cannot hold fish.

What is a pondless water feature?

A pondless water feature is a waterfall or stream that drains into a buried, rock-covered reservoir with no open pond. The water is pumped back to the top and runs down again.

The main parts are an underlayment, an EPDM liner, a reservoir of gravel or matrix blocks, a pump vault, a spillway, flexible PVC pipe and rock. Gravel reservoirs hold only about 30 to 40 percent of their volume as water. Matrix blocks hold about 90 percent or more. Whichever you use, the reservoir must hold all the water that drains back from the stream when the pump stops, plus a margin for top-up.

Pond waterfall vs pondless

Pond waterfall Pondless waterfall
Open water Yes, a visible pool No
Fish Possible, with filtration Not suitable
Debris control Skimmer and filter Keep debris off the rock and out of the vault
Typical fit Larger yards, wildlife and fish Small yards, families with children, lower upkeep
Rough DIY cost Varies widely Kits about $1,000 to $3,000

Pondless does not mean maintenance-free. The pump vault, pump and debris still need regular care.

Can I just build a pond in my backyard?

Yes, many people do. Plan before you dig.

  • Call before you dig. In the US, call 811, or your local utility locate service, a few days ahead so buried lines can be marked.
  • Check local rules. Standing water deeper than a set depth, often around 18 to 24 inches, may need fencing under some local codes. Rules vary.
  • Plan the electrics. A pump needs a GFCI-protected outlet. Hardwired or buried wiring may need a permit and inspection in some areas.
  • Avoid low spots. Runoff can collect in low ground and cause drainage problems.
  • Think about upkeep. A pond needs filtration, cleaning and more regular checks than a pondless feature.

The parts of a waterfall

  • Basin or pond holds the water. A pondless build uses a reservoir instead.
  • Pump moves water from the basin to the top of the falls. Pumps sit in a vault or basin to protect them.
  • Skimmer pulls debris from the surface. Pond waterfalls often pair a skimmer at the far end with a biofalls filter at the top.
  • Spillway is the stone lip where water pours over.
  • Liner is 45 mil EPDM over a geotextile underlayment. It is fish- and plant-safe and often lasts 20 years or more.
  • Flexible PVC pipe carries the water to the top.
  • Black waterfall foam fills gaps behind the stones so water flows over the lip, not under it.
  • Auto-fill valve (optional) replaces water lost to evaporation, which is higher with tall, splashy falls.

How the water flows: head, flow and pipe

Three numbers decide the size of the pump.

  • Flow. A rough rule is about 100, 150 or 200 gallons per hour (GPH) per inch of spillway width for light, medium or heavy flow. Figures vary by brand.
  • Head. The total lift is the vertical distance from the pump to the top of the falls, plus about 1 foot for every 10 feet of pipe to cover friction.
  • Pipe size. About 1.5-inch flexible PVC works up to roughly 3,000 to 4,000 GPH. Larger flows need 2-inch pipe or bigger.

Pumps are rated at zero head, so flow drops as lift rises. Read the pump curve at your calculated head. The figure on the box is the best case.

For the liner, a common size is the length (or width) of the feature, plus twice the maximum depth, plus about 2 feet of overlap.

Building the falls, step by step

  1. Plan the layout. Mark the pond or reservoir, the stream route and the top of the falls.
  2. Dig and set the pump vault. Make the basin or reservoir large enough to hold the drainback.
  3. Lay the underlayment and liner. Leave overlap at the edges and tuck the liner into the corners.
  4. Build the falls. Set level stone shelves with flat lips. A cascade is simply a series of drops like this.
  5. Seal the gaps. Use black waterfall foam behind the stones so the water flows over the lip.
  6. Keep the edges high. Keep liner edges above the water line, because low edges cause most water loss.
  7. Run the pipe, test and adjust. Fill the feature, run the pump and balance the flow with a valve.

For a longer stream build, see building a garden stream.

Keeping pond water clear naturally

Clear water comes from managing the nutrients that feed algae, not from one product.

  • Remove leaves often. Decaying leaves feed algae.
  • Use a skimmer and filtration to catch debris before it sinks.
  • Add aquatic plants that compete with algae for nutrients.
  • Limit direct sun where you can. Too much direct sun feeds algae.
  • Use a UV clarifier for green water, which is suspended algae. String algae does not respond to UV and must be removed by hand.
  • Avoid overfeeding fish. Uneaten food adds nutrients.

Barley straw is sometimes used in ponds, with mixed results. It does less in small, frequently drained features. Expect gradual improvement, not instant clear water.

Do fish like fountains in ponds?

Many fish tolerate moving water, and aeration helps them on hot summer nights. A fountain or waterfall does not replace a filter, though. If your pond has fish, plan the filtration first. Keep some calm water where fish can rest, and avoid aiming a strong spray straight into shallow areas. Pondless features cannot hold fish because they have no open water.

How much does a backyard waterfall cost?

Costs vary with size, materials and labor. These are rough US figures.

  • Pondless DIY kit: about $1,000 to $3,000.
  • Pondless professional install: often several thousand dollars, commonly $3,000 to $15,000 or more, depending on size and materials.
  • Garden pond with a waterfall, professionally built: often $5,000 to $25,000 or more. Koi ponds with full filtration cost more.

Running costs add up too. A 250-watt waterfall pump running all year uses about 2,190 kWh, roughly $370 at 17 cents per kWh. See how expensive water features are for the full breakdown.

What are the three types of waterfalls?

There is no single official list. Backyard waterfalls are usually grouped in three ways:

  1. Pond-fed waterfalls spill into a visible pool.
  2. Pondless waterfalls drain into a buried reservoir.
  3. Stream-style cascades have several drops along a channel. These can be pond-fed or pondless.

Safety

  • Use a GFCI-protected outlet for the pump.
  • Standing water can be dangerous for young children, even when it is shallow. Keep an eye on the feature, use fencing where local rules require it, and consider a pondless design if you have small children.
  • Move heavy boulders with proper technique or equipment. Stone can cause crush injuries.
  • Call 811 or your local locate service before digging.

For a broader view of whether a feature is worth the upkeep, see the simple backyard water features overview. For lighting a waterfall, see pond and water feature lighting.

The complete guide to water features

Simple Backyard Water Features: Types and Ideas
Read the guide

Keep exploring

Guides from other topics

All topics →