A homemade fountain needs a watertight container, a small submersible pump, vinyl tubing and some rocks to hide the reservoir. Seal any drain hole, place the pump in the container, run the tubing up through the rocks, add water, and plug the pump into a GFCI-protected outdoor outlet. A simple build usually takes a few hours plus sealant curing time.
What you need
- A watertight container. A glazed pot, a lined half barrel, a stacked bowl or a buried basin all work.
- A small submersible pump. Look for about 80 to 200 gallons per hour (GPH) at the lift you need.
- Vinyl tubing sized to the pump outlet, often 1/2 inch.
- Rocks or pebbles to cover the pump and hide the tubing.
- Sealant. Use 100 percent silicone labeled as aquarium-safe.
- A GFCI-protected outdoor outlet or a rated extension cord for temporary use only.
Pick a container
Glazed ceramic pots, lined half barrels, stacked bowls and buried buckets or basins all hold water well.
- Unglazed terra-cotta and concrete wick water and leak. Seal the inside with a masonry or pond sealer before use.
- Lined wooden barrels need a pond liner or preformed insert. Raw wood leaks and can leach tannins.
- Galvanized metal can leach zinc, so avoid it where fish will live.
Size the reservoir so it covers several days of evaporation. That way the pump never runs dry between top-ups.
Pick a pump
Choose a pump by the flow you want at the actual lift, which is often 1 to 3 feet. Check the pump curve, because the GPH on the box is measured at zero lift.
Use an inline valve or the pump’s own flow control to tune the spray. Too much flow splashes water out of a small bowl and empties it fast. A bigger pump is not always better.
A solar pump avoids wiring, but it runs only in direct sun unless it has a battery. Solar pumps usually lift water only a short distance.
Build a basic pot fountain
- Seal the drain hole. Plug it with a rubber stopper or cork, then cover it with 100 percent aquarium-safe silicone. Let it cure for 24 to 48 hours before filling.
- Place the pump in the container, on a brick or flat stone so it sits a little off the bottom.
- Attach the tubing to the pump outlet and run it up through the center of the pot.
- Fill the container with water so the pump is fully submerged.
- Cover the pump with pebbles or rocks, leaving the top of the tubing exposed.
- Test the spray. Turn it on, check that the water falls back into the basin, and adjust the flow.
Build a disappearing fountain
A disappearing fountain has a buried basin, a pump and a rigid grate or mesh, with cobbles on top. The water returns underground, so there is no visible pool. Size the buried basin to hold several days of evaporation, and keep the pump accessible for cleaning.
Build a bubbler urn
For a bubbler, pass the tubing up through a hole in the base of the urn and seal around it. Set the pump in a hidden reservoir below. Water bubbles up and over the urn’s rim and returns to the reservoir. Test it before you fill the urn completely.
Seal and drill the container
- Seal the drainage holes and any seams before filling.
- Drill ceramic or stone with a diamond core bit, kept wet, at low speed. Wear eye protection.
- Use aquarium-safe silicone. Household silicone can contain mildewcides that harm fish and wildlife.
- Let sealant cure fully before you add water and fish or birds.
Power and safety
- Plug the pump into a GFCI-protected outdoor outlet with an in-use cover.
- Do not leave an extension cord in place as a permanent fix. If the outlet is too far away, ask a licensed electrician to add one.
- Unplug the pump before you put your hands in the water.
- Keep the cord out of the water and away from places where it could be pulled in.
If you are unsure about the wiring, stop and get help. Electricity and water need care.
Cost and time
A basic DIY pot fountain typically costs about $50 to $200, depending on the container and pump. Build time is a few hours, plus the sealant cure. A disappearing fountain or a bubbler takes longer because of the digging and the reservoir.
Mistakes to avoid
- Using household silicone. Use aquarium-safe silicone.
- Choosing a bigger pump. Too much flow splashes water out and drains the basin.
- Leaving the basin unattended for weeks. A fountain needs regular topping up.
- Leaving the pump on dry. Keep it fully submerged.
- Using a galvanized tub with fish. Zinc can leach from the metal.
For the full range of simple options, see simple backyard water features. For sizing a pump for a bigger pond, see fountains for small ponds. To plan the cleaning routine, see fountain maintenance.