Pumps and Filters

Pond Skimmers: Where to Place Them and Whether You Need One

Do you need a pond skimmer? Learn what it does, where to place it, how to set the water level, and when leaf netting is enough for your pond.

On this page
  1. What a skimmer does
  2. Do you need one?
  3. Where to place it
  4. Set the box level and the water level
  5. Match the flow to the skimmer
  6. Types of skimmers
  7. Installation and leaks
  8. Maintenance
  9. Winter
  10. What a skimmer doesn’t do

Most ponds with trees, wind-blown debris or regular leaf fall benefit from a skimmer. A small fishless wildlife pond with little debris often doesn’t need one. A skimmer is pre-filtration, not a full filter, so it works alongside the rest of the system.

What a skimmer does

A skimmer draws surface water over a floating weir door and catches leaves and debris in a net or basket before they sink and rot. It also removes surface film and scum, which helps gas exchange at the surface. The pump often sits inside the skimmer box, out of sight and easy to reach.

Do you need one?

A skimmer is worth having if:

  • Trees overhang the pond, or leaves blow in.
  • The pond holds fish, where debris decay adds to the waste load.
  • The pond sits in a windy spot.
  • The pond is large, or has an irregular shape.

A skimmer may not be needed if the pond is a small, fishless wildlife pond with little debris. Some small ponds can manage with a net over the surface during leaf fall.

Skimmers don’t remove sunken sludge. That needs a bottom drain or a vacuum.

Where to place it

  • Downwind. Prevailing wind pushes debris toward the downwind side, so the skimmer catches more.
  • Opposite the waterfall or return. The current carries debris across the pond to the skimmer.
  • Use more than one on larger or irregular ponds. How many you need depends on the shape of the pond and the flow.
  • At the edge. Built-in skimmers work best set into the pond edge.

Set the box level and the water level

The skimmer box must be level, with its top just above the water line. The water level should sit about mid-way up the weir. If the level drops too low, the pump can run dry. Many skimmers have an auto-fill valve to keep the level up.

Liners seal to the skimmer faceplate with sealant and bolts. The faceplate is a common leak point, so check it after installation and after any change in water level.

Match the flow to the skimmer

Skimmers have minimum and maximum flow ratings:

  • Too little flow and the weir doesn’t skim well.
  • Too much flow and the water level drops, which can run the pump dry.

A bigger pump doesn’t skim better once the flow passes the weir’s rating. For sizing the pump to the skimmer and the rest of the system, see pond pump and filter setup.

Types of skimmers

  • Surface (floating) skimmers move about the surface and catch debris. They suit small ponds and changing debris patterns.
  • Built-in skimmers are fixed at the pond edge and pull debris in through an inlet. They suit larger ponds and give continuous cleaning.
  • Box skimmers sit on the edge and connect to an external pump. They handle heavy debris.
  • Weir skimmers use a floating weir that adjusts as the water level changes. They suit large ponds.
  • Submerged skimmers sit below the surface and use suction. They are less visible, and work well alongside another skimmer.

Floating skimmers can often be fitted to an existing pump intake without excavation, which makes them a simple retrofit.

Installation and leaks

Set the box on a level base. Seal the liner to the faceplate and bolt it in place. Check for leaks along the faceplate once the pond is full, because that joint is where leaks most often start.

Maintenance

  • Empty the net every few days during leaf fall, and weekly the rest of the year.
  • Check the basket for trapped frogs, newts and small fish. Return any you find to the pond.
  • Clean the filter mats or brushes inside the skimmer. They act as a mechanical pre-filter, and they need cleaning like any other mechanical media. For the rest of the filter, see cleaning a pond filter.

Winter

In very cold climates, many pond owners shut the skimmer and waterfall down for the winter and raise the pump to a shallow shelf (see keeping a garden pond ice-free in winter), so it doesn’t mix away the warmer water at the bottom. How you do it depends on your climate, so check what works locally.

What a skimmer doesn’t do

A skimmer is not a full filter. It catches floating debris, but it does not clean the water chemically or biologically. Sunken sludge stays in the pond, so you still need a bottom drain or vacuum. A skimmer used alongside a bog filter or a biological filter is the usual setup. See bog filters for one option.

The complete guide to pumps and filters

Pond Pump and Filter Setup: Sizing and Plumbing a Pond System
Read the guide

Keep exploring

Guides from other topics

All topics →