Water Features

Pond and Water Feature Lighting: LED Choices and Placement

Choose LED pond lights and place them well: 12-volt transformers on GFCI, submersible ratings, warm color temperature, and aiming up through falling water.

On this page
  1. Low-voltage basics
  2. LED or halogen?
  3. Ratings and materials
  4. Color temperature and color effects
  5. Where to place lights
  6. Timers, photocells and fish
  7. Solar pond lights
  8. Running the cable
  9. Maintenance
  10. Common mistakes
  11. Safety

For most pond and water feature lighting, use LED fixtures rated for submersion, powered by a 12-volt transformer that plugs into a GFCI-protected outlet. Choose warm white in the 2700 to 3000 K range, place the fixtures so they light the water and rock, aim them away from where people sit, and run them on a timer or photocell.

Low-voltage basics

Most pond lighting runs on 12 volts. A transformer steps down the mains power, and it should be plugged into a GFCI-protected outdoor outlet.

  • Keep the load within the rating. Keep the total fixture wattage at or below about 80 percent of the transformer’s rating.
  • Watch the cable length. Long runs cause voltage drop, which makes the lights dimmer toward the end. Use heavier cable, or a hub layout that keeps runs short.
  • Add a photocell or timer. It makes the lights come on at dusk and switch off a few hours later.

LED or halogen?

LED submersible lights typically draw about 1 to 10 watts each. That replaces older halogen fixtures that drew about 20 to 50 watts. The lower draw means less heat, longer life and a smaller transformer.

Ratings and materials

  • Underwater fixtures need an IP68 rating.
  • Splash-zone fixtures are usually rated IP65 to IP67.
  • Housings. Brass and stainless steel last longest. Plastic is the cheapest and degrades faster in sun and water.

Use only fixtures rated for submersion, and only with a GFCI-protected transformer. Do not assume an outdoor light can be put underwater. Many cannot.

Color temperature and color effects

  • 2700 to 3000 K is warm white. It looks natural on rock and water.
  • 5000 to 6500 K is cool white. It looks crisp, sometimes bluish, and can look harsh.
  • RGB fixtures give color effects. Use them sparingly. A single color is often more pleasing than a color show.

More light is not always better. Overlighting makes a feature look flat and harsh.

Where to place lights

Lighting works best when you can see the light, not the lamp.

  • Waterfalls. Place a fixture in the basin just in front of the spill, aimed up through the falling water.
  • Plants, rock and statues. Uplight them from the side or below, and aim the light away from the main viewing area to avoid glare.
  • Hide fixtures. Tuck them behind rocks or plants so the light shows, not the housing.
  • Underwater lights look good only in clear water. In green water they show the murk, not the feature.
  • Avoid pointing lights at the viewer. Glare is unpleasant from a chair or a window.

Timers, photocells and fish

Set the lights to run for a few hours after dusk, then switch them off. Many people use a timer rather than running the lights all night.

Fish benefit from a dark period each night, so a timer is a good choice if you keep fish. Practice varies, so check with a local pond supplier if you are unsure.

Solar pond lights

Solar pond lights are dim and run only for a few hours, depending on the sun. They are fine for accents, such as a small uplight on a rock, but not for lighting a whole waterfall.

Running the cable

  • Bury low-voltage cable at the depth your local code requires. Often that is about 6 inches. See hiding pond pumps, filters and cables for routes and burial depths.
  • Keep the cable clear of digging areas. Mark its route so future digging does not cut it.
  • Make connections above water, in housings rated for the job. Do not leave bare connections where water can reach them.
  • Keep the transformer dry and off the ground, and plugged into the GFCI outlet.

Maintenance

  • Clean the lenses every 1 to 2 months. Algae and silt dim the output quickly.
  • Check the seals on each fixture after a season of wet weather.
  • Replace failed fixtures with the same rating. A cheaper, unrated fixture is not a safe swap.
  • Check the cable after storms or digging.

For algae control and clean water in the basin, see fountain maintenance.

Common mistakes

  • Buying the most lumens. Overlighting looks harsh.
  • Pointing lights at the viewer. Aim them up, across or at the feature.
  • Assuming any outdoor light can be submerged. Only use submersion-rated fixtures.
  • Expecting lights to clear water. Lighting shows clarity. It does not improve it.

Safety

  • Use only fixtures rated for submersion.
  • Use a GFCI-protected transformer.
  • Bury cable at the depth your local code requires, and keep it clear of digging.
  • If you are unsure about the wiring, ask a licensed electrician.

For lighting a waterfall, see pond waterfalls and pondless water features. For a pond fountain, see fountains for small ponds. For the simple water feature options, see simple backyard water features.

The complete guide to water features

Simple Backyard Water Features: Types and Ideas
Read the guide

Keep exploring

Guides from other topics

All topics →