Water Features

How to put a fountain in a pond?

To put a fountain in a pond, pick a pump for your pond size and spray height, set it on a brick, anchor or position it, and power it from a GFCI outlet.

On this page
  1. Before you start
  2. Installing a submersible fountain
  3. Installing a floating fountain
  4. Power and safety
  5. Test and adjust
  6. Common mistakes
  7. After installation

To put a fountain in a pond, choose a pump that matches your pond size and spray height. Then either set a submersible pump on a brick a few inches off the bottom, or anchor a floating unit with lines. Route the cord to a GFCI-protected outlet, plug it in, and tune the flow. Test it before you walk away.

Before you start

  • Check the flow at your real height. Pumps are rated at zero lift. Use the flow at the height the water will travel, not the figure on the box. For sizing, see fountains for small ponds.
  • Plan the cord route. Find a GFCI-protected outdoor outlet within reach. If none is nearby, ask a licensed electrician about adding one.
  • Check the maker’s minimum depth. Minimum depths vary by model.
  • Call before you dig. If you are trenching for a cord, call 811 in the US, or your local utility locate service, first.

Installing a submersible fountain

  1. Unplug any existing equipment.
  2. Fit the telescoping riser and nozzle to the pump outlet.
  3. Set the pump on a brick or flat stone so it sits a few inches off the bottom. This keeps it from pulling in mud.
  4. Adjust the riser so a bell nozzle sits just above the surface. Most other nozzles sit at or just above the surface.
  5. Lower the pump in at an angle so trapped air can escape. Submersible pumps prime themselves once they are underwater.
  6. Run the cord under edge stones or through conduit (see hiding pond pumps, filters and cables), then plug it into the GFCI outlet.
  7. Tune the flow-control valve to set the height and limit overspray.

Installing a floating fountain

  1. Assemble the unit. Bolt the motor or pump to the float with the hardware the maker supplies. Fit the bottom intake screen so leaves and muck do not reach the pump. Attach the nozzle you want.
  2. Set up power. Many smaller units plug into a standard outlet through a GFCI-protected timer box. Larger units may need a licensed electrician to wire a control panel.
  3. Attach the ropes. Tie two or three nylon mooring ropes or stainless cables to the float’s attachment points.
  4. Anchor it. Drive stakes or use weights on opposite sides of the pond and center the fountain between them. Duckbill anchors and deadweights both work.
  5. Leave slack. Allow extra rope and cord so wind, spin and seasonal water-level changes do not pull the unit over.
  6. Launch and check. Float the unit into place and plug it in. Adjust the ropes if it spins or drifts.

Never lift or tow the fountain by its cord, and never plug in or switch on the pump while it sits out of the water.

Power and safety

  • Use a GFCI-protected outdoor outlet with an in-use cover.
  • Do not use an extension cord as a permanent power supply.
  • Never cut the plug off to feed the cord through conduit. It is unsafe and voids the warranty.
  • Larger or high-horsepower units should be wired by a licensed electrician, with GFCI protection on the control panel.
  • Unplug the pump before your hands go in the water.

If you are unsure about any of the wiring, stop and ask a licensed electrician. Electrical mistakes near water are dangerous.

Test and adjust

  • Watch the spray for a few minutes. It should land inside the pond, not on the edge or the surrounding lawn.
  • Keep the spray a few feet away from water lilies, which dislike turbulence.
  • If you hear gurgling, tilt the pump briefly to purge trapped air.
  • Check the ropes and cord again after the first windy day.

Common mistakes

  • Setting the pump on bare mud. Lift it a few inches on a brick or stone so it does not pull in sludge.
  • Assuming any “fountain pump” fits any pond. Pump flow, lift and nozzle all matter.
  • Treating the fountain as a filter. A fountain adds oxygen but does not remove waste. That is the job of a pump and filter system.
  • Cutting the plug to fit a conduit, which is unsafe.

After installation

Clean the pump intake every 1 to 4 weeks, depending on how much debris reaches it. For the cleaning routine, see fountain maintenance. If the pump later hums but moves no water, follow the steps in how to unclog a water fountain.

The complete guide to water features

Simple Backyard Water Features: Types and Ideas
Read the guide

Keep exploring

Guides from other topics

All topics →