Pond Building

How to Build a Garden Pond: Planning, Digging and Design

Plan, dig and line a backyard garden pond step by step, from 811 calls and site choice to depth zones, underlay, liner, filling and pump basics.

On this page
  1. Plan the site before you dig
  2. Choose the size and shape
  3. Set the depth zones
  4. Work out the liner size
  5. Dig the pond in stages
  6. Lay the underlay and liner
  7. Fill the pond and treat the water
  8. Plant for balance
  9. Add a pump and filter
  10. Finish the edges
  11. Common questions
  12. Common mistakes
  13. Safety

Plan the site before you dig

Start with the two calls that matter most. In the US, call 811 a few business days before you dig so buried utility lines are marked. Lead times vary by state. In the UK, check utility plans or use a cable detector. Do not dig near gas or power lines until they have been located.

Then choose the spot:

  • Sun. A pond does not need full sun all day. Roughly 4 to 6 hours of direct sun is usually ideal, and water lilies tend to bloom best with about 6 hours.
  • Trees. Avoid overhanging trees. Falling leaves foul the water, and roots can damage a liner.
  • Low spots. Do not put the pond in the lowest part of the garden. It collects runoff, silt and debris. If water runs in from higher ground, divert it first. The sloped garden article covers that case.
  • Power and water. Pumps need a GFCI (US) or RCD (UK) protected outlet, and a nearby hose makes topping up easy.
  • Visibility. If children visit, keep the pond within sight of the house.

Keep the pond clear of house foundations, septic systems and wells. Setback distances vary by location, so check local rules. The setback guide goes into the details. If you are still deciding whether a pond suits your property at all, the pros and cons article weighs the costs and benefits.

Choose the size and shape

Bigger is not always easier. Small volumes swing more in temperature and water quality, so a small pond needs the same care with planting and filtration as a larger one.

To estimate the volume, multiply the length, width and average depth:

  • US: length × width × average depth (ft) × 7.48 = gallons
  • Metric: length × width × average depth (m) × 1,000 = litres

For example, a pond 10 ft by 8 ft with an average depth of 1.5 ft holds roughly 900 gallons (10 × 8 × 1.5 × 7.48 ≈ 898).

Curved outlines are often easier to blend into the garden and make the rim easier to hide. Formal rectangular shapes need a more carefully levelled rim and neater edging. Either can work well.

Set the depth zones

The depth you choose depends on what you want to keep in the pond.

  • Garden pond with plants and goldfish: the deep area is usually 18 to 24 inches (45 to 60 cm).
  • Koi: at least 3 ft (90 cm), and 4 to 6 ft is better. The two-foot depth question explains why.
  • Wildlife pond with no fish: a shallower zone of around 12 to 18 inches, with gently sloping edges, lets frogs, newts and birds get in and out.
  • Cold climates: many builders aim for 30 to 36 inches so fish can overwinter. This varies, so check local advice.

Cut shelves 8 to 12 inches (20 to 30 cm) deep and 8 to 12 inches wide around the edge for marginal plants. Steep side walls make it harder for wading herons to reach fish, but walls that are too steep need the liner and soil to be stable.

Work out the liner size

Use the maximum depth, not the average depth, when you size the liner:

  • Length: pond length + (2 × maximum depth) + about 2 ft (60 cm) of overlap
  • Width: pond width + (2 × maximum depth) + about 2 ft (60 cm) of overlap
  • Metric: add 2 × depth + 60 cm instead of 2 ft

The liner has to run down one side, across the bottom and back up the other side. A 10 ft by 8 ft pond with a 2 ft maximum depth needs a liner about 16 ft by 14 ft (10 + 4 + 2 by 8 + 4 + 2). Liner types differ in thickness, flexibility and lifespan. The pond liners and sealants guide compares them, and the preformed pond kits guide covers pre-moulded shells.

Dig the pond in stages

  1. Mark the outline. Lay out the shape with a garden hose or rope, then step back and check it from the house and the patio.
  2. Dig in tiers. Dig the shelves to their depth around the edge, then excavate the deeper zone. Check depths as you go.
  3. Level the rim. The rim has to be level all the way round, even when the ground around it is not. Check with a laser level, a water level or a long board and spirit level. A rim that is out by about 1 inch (2 to 3 cm) exposes the liner on the high side.
  4. Clear the hole. Remove stones, sharp roots and debris. Anything sharp left in the base can puncture the liner.
  5. Keep the walls safe. Lined holes and water are heavy, and unsupported walls can collapse. Do not dig deep trenches without shoring them up.

Lay the underlay and liner

Underlay protects the liner from stones and roots. Two options are common:

  • Non-woven geotextile (polyester or polypropylene) is the best general choice. Typical weights are 4 to 8 oz per square yard, and heavier fabric (about 8 to 10 oz, or 300 g/m² or more) suits stony ground and koi ponds. Overlap seams by about 6 in (15 cm).
  • Damp sand works well on the floor, at about 2 in (5 cm) deep. It slides off steep walls, so use geotextile on the sides.

Avoid newspaper and cardboard, which decay quickly. Old carpet can work if it is untreated, but natural fibres rot over time. The underlayment guide explains the options in more detail.

Lay the liner over the underlay, press it into the shelves and walls, and weigh the edges down with rocks or bricks. Leave the excess at the edge and trim it only after the pond is full.

Fill the pond and treat the water

Fill the pond slowly. Smooth the folds in the liner as the water rises so it settles into its shape.

Treated tap water usually contains chlorine or chloramine. Standing water for a day or two can drive off chlorine, but not chloramine, which many utilities use. A dechlorinator removes both, so use one before anything goes into the pond. Rainwater is a good choice for wildlife ponds if you can collect enough.

Let the water settle and test it before you add fish. Many builders wait a week or more after filling before stocking.

Plant for balance

Aim to cover about half to three-fifths of the surface with plants. The guideline is roughly 50 to 60%, and it varies with the pond. Marginal plants on the shelves, floating plants and oxygenating plants all help. Plants shade the water and use up nutrients that would otherwise feed algae.

Depth alone does not stop algae. Shade, plants and filtration matter more.

Add a pump and filter

A pump keeps water moving and can power a fountain or waterfall. Kit pumps are often undersized for fish, so check the flow rate in gallons per hour against the pond’s volume before you buy.

Filtration keeps the water clear. A skimmer pulls surface debris, and a biological filter supports the bacteria that break down waste. A skimmer is not an overflow, so the overflow article covers how to handle heavy rain.

Keep all electrical connections well above the maximum flood level.

Garden ponds usually have no bottom drain. Koi ponds often do. Bottom drains are hard to add to a finished pond, so decide before you build. The bottom drain article explains how they work and how they differ from pool drains.

Finish the edges

Hide the liner with flat stones, coping or overhanging stones. The liner must not show above the water line, because UV light degrades exposed liner. Plant around the rim to soften the edge. Leave a shallow, sloping edge or a log so frogs and small animals can get out.

Common questions

Can I just dig a hole to make a pond?

Usually not, at least not one that holds water reliably. Bare soil leaks and can collapse, so a pond needs a liner or a properly sealed base. Clay soil helps, but it is not automatically watertight, and garden ponds on clay usually still need a liner. The clay soil article explains why.

Should a pond have gravel in the bottom?

Gravel is optional. A thin layer can cover the liner, look natural and give beneficial bacteria a surface to colonise. Deep gravel traps debris that rots, so keep it shallow and clean it regularly.

How deep should a pond be for fish?

For goldfish and plants in a mild climate, 2 ft (60 cm) is often enough. Koi need at least 3 ft (90 cm), and 4 to 6 ft is better.

How do I keep algae out of my pond?

There is no single fix for pond algae. Aim for about 4 to 6 hours of sun, cover part of the surface with plants, use filtration that can handle the number of fish you keep, and avoid overfeeding. Depth alone will not stop algae.

Common mistakes

  • Choosing the lowest spot in the garden, where runoff and debris collect.
  • Sizing the liner from the average depth instead of the maximum depth.
  • Skipping underlay, so stones puncture the liner.
  • Using house, masonry or pool paint as a pond coating. The coating guide covers what is suitable.
  • Adding fish on the first day, before the water has settled and been tested.

Safety

Children can drown in just a few inches of water. Fence the pond, or cover it, wherever small children visit. Local codes often treat water deeper than about 18 to 24 inches as needing a fence, but the rules vary, so check locally and with your home insurer.

Power pumps only from GFCI (US) or RCD (UK) protected outlets. Lift heavy stone with help or proper technique, and do not work in an unsupported trench.

Keep exploring

Guides from other topics

All topics →