Algae and Water Quality

Pond Ammonia and Nitrite: How to Test, Read and Lower Them

Ammonia and nitrite should read zero in a healthy pond. Learn how to test them, read the results and lower them safely, and see why pH matters.

On this page
  1. How the nitrogen cycle works
  2. Test ammonia and nitrite
  3. Why pH and temperature change the risk
  4. Lower ammonia step by step
  5. Nitrite and salt
  6. Cold water and chloramine
  7. Signs of trouble in fish
  8. Common myths
  9. Common questions
  10. Safety

Ammonia and nitrite should read zero in a healthy pond. Both are toxic to fish, and both are signs that the nitrogen cycle is falling behind. Fish waste, uneaten food and decaying matter produce ammonia. Beneficial bacteria convert it to nitrite, and then to much less harmful nitrate. When that process lags, the readings climb and fish suffer.

Short answer: if ammonia or nitrite reads above zero, stop extra feeding, do a partial water change with dechlorinated water, add aeration, and add nitrifying bacteria. Test every day or two during a spike, and read the results alongside pH and temperature.

How the nitrogen cycle works

  • Ammonia comes from fish waste (much of it is excreted through the gills), uneaten food, decaying plants and leaves, and dead fish.
  • Nitrifying bacteria convert ammonia to nitrite, and then nitrite to nitrate.
  • Nitrate is much less toxic. Keep it below about 40 ppm, using plant uptake and water changes.

A new pond typically takes four to eight weeks to build up the bacteria that run this cycle. An unseeded new filter can take four to six weeks on its own. Beneficial pond bacteria explains the nitrifying products and how to dose them.

Test ammonia and nitrite

The targets are zero for both. In these tests, ppm and mg/L are the same.

  • Use a liquid test kit rather than strips. Liquid kits are generally more accurate. During a spike, test every one to two days.
  • Read results with care. Ammonia binders such as Seachem Prime and API Ammo Lock detoxify ammonia, but tests may still read positive afterward. Nessler-type kits can read falsely high.
  • Know the danger points. Long-term harm can start around 0.02 to 0.05 mg/L of un-ionized ammonia (NH3). Nitrite interferes with oxygen transport in the blood, a problem sometimes called brown blood disease.

Why pH and temperature change the risk

Only the un-ionized form of ammonia (NH3) is highly toxic, and its share rises with pH and temperature. At 77°F (25°C), about 0.6 percent of total ammonia is NH3 at pH 7.0, and about 5 percent is at pH 8.0.

The same total ammonia reading is more dangerous at pH 8.5 than at pH 6.5. Keep pH stable and in range. The pond pH guide explains how to test and adjust it.

Lower ammonia step by step

Work through these in roughly this order:

  1. Stop or cut feeding for two to three days. Less food means less ammonia.
  2. Do a partial water change of about 10 to 25 percent with dechlorinated water at about the pond’s temperature. Repeat as your readings require.
  3. Add aeration. Bacteria need oxygen to convert ammonia.
  4. Dose nitrifying bacteria (a “filter start” product), following the label.
  5. Remove decaying matter. Take out dead leaves, dead plants and any dead fish.
  6. Reduce stocking if the fish load is higher than the filter can handle.
  7. Don’t over-clean the filter. Rinse media in pond water, not tap water, so the bacteria survive.

An ammonia binder can make ammonia less harmful in the short term while the bacteria catch up. It doesn’t fix the cause, so keep working through the steps above.

Nitrite and salt

Salt can reduce nitrite toxicity in fish. About 0.1 percent salt (1 gram per liter, roughly 1 pound per 120 US gallons) is a commonly used level. Many pond plants are salt-sensitive, though, and salt does nothing for ammonia. Check your plants and fish before adding salt, and treat it as a short-term measure for nitrite.

Cold water and chloramine

  • Stop feeding below about 50°F (10°C). Nitrifying bacteria slow down sharply in cold water. Between 50 and 60°F, a wheat-germ-based food is often used, if your fish will eat it.
  • Use a dechlorinator rated for chloramine if your water supplier uses it. Chloramine doesn’t simply evaporate. A dechlorinator that isn’t rated for it can break the chloramine down and release ammonia into the pond.

Signs of trouble in fish

Watch for gasping at the surface, lethargy, red or inflamed gills, clamped fins and loss of appetite. These can also come from low oxygen or a pH problem, so test the water rather than guessing from the fish alone.

Common myths

  • A clear pond is safe. Ammonia is invisible.
  • A large water change is always best. Big swings in temperature and pH stress fish. Partial changes are safer.
  • Cleaning the filter thoroughly in tap water helps. It kills the bacteria.
  • Any ammonia reading is equally dangerous. The risk depends on pH and temperature.

Common questions

How do I lower ammonia in pond water? Stop extra feeding, do a partial water change with dechlorinated water, add aeration, and dose nitrifying bacteria. Test every day or two until the readings return to zero.

Should I worry about nitrate? Keep it below about 40 ppm. Plants, water changes and removing organic waste keep it in check.

Safety

  • Wear gloves when handling pond water and sludge, and cover any cuts.
  • If fish are dying, or readings stay high after the steps above, get help from a fish vet or pond specialist quickly.
  • Keep test chemicals and treatments away from children and pets.

For odors that often come with ammonia or sludge, see the pond smell guide.

The complete guide to algae and water quality

How to Get Rid of Pond Algae and Keep It Away
Read the guide

Keep exploring

Guides from other topics

All topics →