Why a garden pond needs an overflow
Rain adds water to a pond, and it often adds more than you would expect. A pond collects runoff from the surrounding lawn, patio and roof as well as the rain that falls straight onto the surface. Without a way to release the excess, the water rises over the rim and can wash out fish, erode the edges, and spread silt and fertiliser into the garden.
An overflow sets the highest level the pond will reach, and it sends any excess water somewhere safe.
How much water heavy rain adds
A simple rule of thumb helps with planning. One inch (25 mm) of rain on 100 square feet adds about 62 gallons of water, because each square foot takes up about 0.623 gallons per inch of rain. In metric, 1 mm of rain on 1 m² adds 1 litre.
Runoff from patios, lawns and roofs can add far more than the rain that falls on the pond itself. Divert that runoff away from the pond before you rely on the overflow alone. A bigger pipe does not solve runoff that is flowing into the pond in the first place.
Set the overflow level
The overflow inlet should sit about 1 to 2 inches (2 to 5 cm) below the top edge of the liner. That gives the pond a margin before water reaches the rim, and it keeps the water level at a height the liner and edging were designed for.
Check the level after you fill the pond and after any change to the edging. A small change in the rim height can move the overflow point.
Choose an overflow style
Several designs work for garden ponds:
- Pipe through the liner. The most common option. The pipe passes through the liner with a bulkhead fitting or tank connector, and gaskets sit on either side of the liner to make a watertight seal. The inlet should be screened (see below).
- Standpipe in a filter chamber or skimmer. A standpipe sets the maximum water level, and the excess flows down through the chamber. A skimmer with a set level can do this job, but a skimmer is not an overflow on its own unless it is set up to take the excess.
- Wick overflow. A gravel trench at a low point of the edge lets water spill out gradually. It suits wildlife ponds, where a fixed pipe would be less natural.
Whichever you choose, the outlet must be sealed where it passes through the liner. An unsealed penetration is a common source of leaks.
Size the pipe and set the slope
Common overflow pipe sizes are 2 to 4 inches (50 to 110 mm). Larger catchments, such as a pond fed by a big roof or a sloping lawn, need a larger pipe. The right size depends on the area that drains to the pond.
Slope the pipe so water drains freely. At least 1/4 inch per foot (about 2%) fall is a common minimum. A pipe laid flat can hold water and let debris settle inside it.
Screen the inlet
Put a screen over the overflow inlet. Without one, fish, frogs and debris can escape through the pipe or block it. A blocked overflow does nothing when you need it most, so check the screen regularly.
Where the water goes
Send the overflow water somewhere it can soak away or drain safely:
- A rain garden or soakaway, where the ground can take the water
- A dry well
- A storm drain, where local rules allow it
Discharge to a sewer may be prohibited in some areas, so check local rules before connecting to one.
Do not discharge onto a neighbour’s property, and do not point the outlet toward a house foundation. Water running against a foundation can cause damage over time. The setback guide covers the distances to keep between a pond and a house.
Keep the overflow working
An overflow only works when it is clear, so build in a few routine checks:
- Check before storms and after leaf fall, when debris is most likely to block the inlet.
- Clear the screen and the pipe, and check the outlet is still draining.
- Automatic top-up valves need an overflow. If the valve sticks open, the overflow stops the pond from flooding.
- Keep electrical connections for pumps and lights well above the maximum flood level.
Overflow and the wider pond
An overflow handles water above the set level. It does not drain the pond, and it does not stop water entering from runoff. If the surrounding ground drains into the pond, the sloped garden article covers how to divert it. The garden pond guide covers the full build, and the liners article covers how to seal a liner penetration.
Larger ponds and earth dams
This article covers garden-scale ponds with a liner. Large ponds and earth dams are a different job. Spillways on a dam need to be sized for peak flood flows, and the pipe passes through the dam itself, which is a structural concern. For those, get advice from a professional. In the US, the Natural Resources Conservation Service (NRCS) offers free technical guidance on farm pond design.
Common mistakes
- Assuming the pond will “just overflow harmlessly”. Flooding can wash out fish and erode edges.
- Expecting the overflow to drain much water. It only removes what is above the set level.
- Treating a skimmer as an overflow without setting it up for that job.
- Fitting a bigger pipe instead of diverting the runoff that causes the flooding.
- Leaving the inlet unscreened, or letting it clog with leaves.
Safety
Keep electrical connections well above the maximum flood level. Check the outlet is not discharging onto a path where people walk or near a foundation. Remember that a flooding pond can wash out the edges, so check the rim after heavy rain.