Pond Building

Preformed Ponds and DIY Pond Kits: What to Buy and How to Install Them

Choose a preformed pond or DIY kit, size it for fish and pump flow, then bed it on damp sand, back-fill as you fill and keep the rim clear of runoff.

On this page
  1. Preformed ponds and kits: what they are
  2. Sizes and depth
  3. Check the kit pump
  4. Install a preformed shell
  5. Backfill and fill together
  6. Above-ground preformed ponds
  7. Hide the rim
  8. Common questions and mistakes
  9. Safety

Preformed ponds and kits: what they are

A preformed pond is a rigid shell, usually made from HDPE or other polyethylene, or from fibreglass. Plastic shells are the cheaper option. Fibreglass shells are stiffer and often last longer, with 20 years or more quoted for good quality. Thin plastic can crack or warp sooner, so check the thickness and the warranty before you buy.

A DIY pond kit is a shell or a flexible liner packaged with other parts. A typical kit includes the liner, underlay, a pump, and sometimes a filter, tubing and a fountain head. Read the list before you buy, because a kit that looks complete may still need extra parts.

Sizes and depth

Preformed ponds range from roughly 50 to 500 gallons (200 to 1,900 litres). Most are 18 to 24 inches deep or shallower.

That makes them suitable for goldfish, plants and wildlife. Koi need much more depth and volume, and most kits do not hold enough water for them. The two-foot depth question explains the depth koi need, and the raised pond guide covers a larger, built-up option.

A small volume also means the water warms and cools quickly, so keep the number of fish modest.

Check the kit pump

Pumps in kits are often undersized for the fish you want to keep. Compare the pump’s flow rate, in gallons per hour, against the pond’s volume before you buy. A larger pump usually gives the water better circulation, but it also uses more power, so match the pump to the pond rather than picking the biggest one.

Power every outdoor pump from a GFCI (US) or RCD (UK) protected outlet.

Install a preformed shell

  1. Trace the outline. Turn the shell upside down and trace around it, or mark the shape with stakes.
  2. Dig. Dig a hole about 2 in (5 cm) wider and deeper than the shell.
  3. Dig the shelves to match the shell’s profile. The shelves must be fully supported, not hanging over empty ground.
  4. Bed the shell. Lay 2 in (5 cm) of damp sand across the base. Remove any stones or roots first, because sand alone will not level a rocky base.
  5. Set the shell and check the level. Place the shell and check the level front to back and side to side. Set the rim about 1 in (2 to 3 cm) above the ground so runoff stays out.

Backfill and fill together

Fill the shell with water about 4 in (10 cm) at a time, backfilling soil or sand around the outside as you go. Keep the backfill even on all sides, so the shell is supported as the water rises.

Recheck the level several times during filling. An unlevel rim shows up on one side first, and it is much easier to correct early. Do not backfill before the shell has water in it, because the weight of the soil can distort the shell. The garden pond guide covers the general digging and filling steps for lined ponds.

Clay soil can be a problem for rigid ponds, because it swells and shrinks with moisture. The clay soil article covers the tests and the precautions.

Above-ground preformed ponds

An above-ground preformed pond needs support on every side. Use a frame, a raised bed, or full backfill all the way round. A shell that stands on its own above the ground is likely to flex, crack or tilt.

Above-ground ponds also feel the cold more than sunk ones, because the surrounding soil does not insulate the water. In cold climates, plan for freezing, and consider a de-icer or a way to move fish indoors.

Hide the rim

UV light degrades exposed plastic, so hide the rim. Overhanging stones, plants or a coping edge all work. Keep the stones secure, and leave a sloping or stepped edge where frogs and small animals can climb out.

Common questions and mistakes

Should a pond have gravel in the bottom?

It is optional. A thin layer of gravel can look natural and give beneficial bacteria a surface, but deep gravel traps debris. Keep it shallow.

Is a kit pond big enough for koi?

Usually not. Most kits hold too little water and are too shallow for koi. A larger, deeper pond is needed, as covered in the raised pond guide.

Can I just build a pond in my backyard?

Yes, but plan the build first. A preformed shell or kit still needs a level, supported base, a sensible location and a safe, correctly sized pump.

Common mistakes

  • Treating a preformed pond as install-and-forget. Poor backfill is the usual cause of cracks.
  • Backfilling before the water goes in, which distorts the shell.
  • Assuming a preformed shape is stronger than a lined pond when the base is not supported.
  • Buying a kit pump that is too small for the fish.

Safety

Use a GFCI (US) or RCD (UK) protected outlet for the pump. Keep the cable and connections well above any flood level. Children can drown in a few inches of water, so fence or cover the pond where children visit.

The complete guide to pond building

How to Build a Garden Pond: Planning, Digging and Design
Read the guide

Keep exploring

Guides from other topics

All topics →