Pond Building

What kind of paint can I use to seal my pond?

Only use coatings sold as pond- or fish-safe to seal a pond. Learn why house, masonry and pool paints fail, plus cure times and surface prep.

On this page
  1. Short answer: use a coating sold as pond- or fish-safe
  2. Which paints are not safe
  3. Coating types that work
  4. Check the label before you buy
  5. Prepare the surface
  6. Cure, rinse and fill
  7. What a coating does and does not fix
  8. Colour
  9. Common questions
  10. Safety

Short answer: use a coating sold as pond- or fish-safe

Use a coating sold specifically as pond- or fish-safe. Ordinary exterior, masonry and house paint is not safe for fish, and pool paint is not the same thing as pond paint. Look for fish-safe wording on the label before you buy, and check the product’s cure time, because it has to cure fully before fish go in.

Which paints are not safe

Do not use these for a pond:

  • House, masonry and exterior paint. These are not made for constant immersion in water with animals in it.
  • Swimming pool paint. Pool paint is not the same as pond paint, and some pool paints contain biocides.
  • Driveway and concrete sealers. These are not designed for constant immersion.

Painting over a leaking liner does not fix the leak. Patch the liner with its repair kit instead.

Coating types that work

Coatings sold for ponds usually fall into three types:

  • Two-part epoxy. Hard and durable. It needs good ventilation and gloves during application.
  • Polyurethane. Some products are moisture-curing. Check the label for the conditions it needs.
  • Liquid or rubberised coatings. These can bridge hairline cracks in the surface.

For a koi pond built from block or concrete, a fibreglass (GRP) resin lining is also a durable alternative. It is a specialist job, so get it done by someone experienced.

Is pond paint safe for fish?

It can be, but only when the product is sold as fish- or pond-safe and has been fully cured and rinsed. NSF/ANSI 61 certification, which covers potable water, is a good sign that the cured coating is non-toxic. Not every pond product carries it, so check the label.

Check the label before you buy

Before you buy, check:

  • Fish-safe or pond-safe wording, and whether the product is NSF/ANSI 61 certified.
  • Application limits for temperature and moisture. Many products cannot be applied in cold or damp conditions.
  • Cure time before filling.
  • Coverage for the area you need to seal.

Prepare the surface

Good preparation matters more than the product. The surface must be clean, dry and sound. Remove any loose laitance (the weak, powdery layer on new concrete), and etch or abrade the surface as the product instructions say.

Structural cracks need repair before you coat. A liquid coating can seal hairline cracks, but it will not hold a crack that is moving or wide.

How to apply pond sealer?

Follow the product’s instructions to the letter. Prepare and clean the surface, mix the coating as directed, and apply it at the coverage rate and within the temperature and moisture limits on the label. Work in ventilated conditions, and wear gloves and eye protection for two-part products.

Cure, rinse and fill

New concrete should cure for about 28 days before you coat it. Uncoated new concrete leaches lime and can push the water’s pH above 9, so do not skip the cure or the coating.

Once the coating is on, let it cure fully before filling. Depending on the product and the temperature, that can take several days to about a week. Rinse and drain the pond once after the cure, following the manufacturer’s advice, and only then add fish. The raised pond guide covers how the coating fits into a block-built koi pond.

What a coating does and does not fix

A coating seals the surface. It does not fix every problem:

  • It can seal hairline cracks, but structural cracks need repair first.
  • It does not fix a leaking liner, so patch a liner rather than painting over it.
  • It does not replace a waterproof wall. Concrete alone is not waterproof, and a coating is part of the waterproofing system.

The liners and sealants guide compares coatings with flexible liners and covers the checks to make before you choose.

Colour

Coating colour changes how the pond looks. Black and dark colours make the pond look deeper and hide algae and debris, while light colours show more of the water’s condition. Choose a colour you can keep clean.

Common questions

Can I use pool paint on my pond? No. Pool paint is not the same as pond paint, and some pool paints contain biocides that are not suitable for fish.

Does paint dry quickly like house paint? No. Pond coatings must cure fully, which can take days, so leave them alone until the cure is complete.

Is a coating enough on its own? It depends on the wall. Block walls need a waterproof system, and a coating is one part of that.

Safety

Two-part epoxies and polyurethanes need gloves, eye protection and good ventilation. Follow the label for the safety steps. Keep fish out of the pond until the coating has fully cured and been rinsed.

The complete guide to pond building

How to Build a Garden Pond: Planning, Digging and Design
Read the guide

Keep exploring

Guides from other topics

All topics →