Pumps and Filters

Pond Pump Not Working: Troubleshooting Common Faults

Pond pump not working? Check power and the GFCI first, then water level, the intake and airlocks. A symptom-by-symptom guide to common pump faults.

On this page
  1. Stay safe first
  2. Check the power
  3. Match the symptom to the fault
  4. Low water and dry running
  5. Clear a blocked intake and impeller
  6. Clear an airlock
  7. Limescale
  8. Test the pump on its own
  9. When the pump needs replacing
  10. Winter storage
  11. Common mistakes

Most pond pumps that seem dead have one of three problems: no power, low water, or a blocked intake. Check those first. Only suspect the motor once they are ruled out.

Stay safe first

  • Unplug the pump before you touch, clean or lift it. Never lift it by the cord.
  • Reset a tripped GFCI or RCD once. If it trips again straight away, stop. A cable or motor fault is likely, so don’t keep resetting it. The pump may need replacing.
  • Call a licensed electrician if the trip continues after you have checked the outlet and the cord.
  • Don’t cut and splice the sealed cord. That breaks the waterproofing and usually voids the warranty.
  • Don’t open a sealed motor housing. Capacitor work on an external pump is a job for an electrician.

Check the power

  1. Plug a device you know works, such as a lamp or a phone charger, into the same outlet. If it doesn’t power up, the fault is in the outlet or the supply.
  2. Reset the GFCI. If it trips again straight away, follow the safety steps above.
  3. Check the breaker in the main panel. A breaker may have moved to the middle position.

Match the symptom to the fault

What you see Likely cause What to do
No sound and no hum No power, a tripped GFCI, or a failed cord Check power, reset the GFCI once, test the outlet
Hums or buzzes but no water Jammed impeller, airlock, or blocked intake Unplug, clear the impeller and intake, release any air
Slurping or gurgling sound Water too low at the pump (cavitation) Top up the pond, clean the filters, check for leaks
Runs, but flow is weak Clogged pre-filter or filter, kinked hose, closed valve, or too much head Clean the pre-filter and filter, straighten the hose, open valves
Rattling or grinding Worn bushings or a damaged impeller Inspect the impeller and bushings, then repair or replace
Stops from time to time Thermal cut-out, or the pump running dry Let it cool, then check the water level

Low water and dry running

Keep the water above the pump’s intake. Many skimmers and pumps need water at a set level to work safely. Dry running damages bushings and seals quickly. Never run a pump dry to test it.

Hot weather evaporation can lower a pond quickly, so top it up regularly. If the level falls faster than evaporation explains, check for pond leaks. Some pumps have a thermal cut-out that resets after cooling. If your pump keeps cutting out, check the water level and the cooling before you assume a fault.

Clear a blocked intake and impeller

  1. Unplug the pump.
  2. Clean the intake screen, skimmer basket and filter pads.
  3. Remove the pump cover, and clear out pebbles, twigs, mulch or string algae from the impeller.
  4. Turn the impeller by hand. It should spin freely, without seizing or cracking.
  5. Check the ceramic shaft for cracks. It is brittle. Check the rubber bushings for wear.

Clear an airlock

Unplug the pump, submerge it fully, and tilt or gently shake it so the trapped air escapes. Then restart it. External pumps need priming or a flooded suction to keep working.

Limescale

Hard water leaves limescale on the impeller and housing. Soak them in white vinegar or citric acid for a few hours, then rinse them before you refit the pump. Small fountain pumps descale the same way, as covered in how to unclog a water fountain.

Test the pump on its own

Disconnect the hose and check the flow at the outlet with the pump in the water. If the pump moves water well on its own, the fault lies in the plumbing or the filter. Look for a kinked hose, a closed valve, a blocked filter or a stuck check valve. A new pump won’t fix low flow caused by plumbing or the filter.

When the pump needs replacing

Magnetic-drive pumps typically last about 3 to 5 years of 24/7 running, though the figure varies widely. Some manufacturers offer repair or rebuild services, so check before you buy new.

External pumps can have a leaking shaft seal, or a failed start capacitor that makes them hum but not start. A capacitor fault is for an electrician to fix.

Winter storage

Some manufacturers advise storing magnetic-drive pumps in a bucket of water in a frost-free place over winter. Check your pump’s manual before you store it.

Common mistakes

  • Lifting the pump by its cord. This can damage the cord and its seal.
  • Assuming a humming pump is dead. It is often just jammed.
  • Replacing the pump for plumbing faults. A new pump won’t fix a kinked hose or a blocked filter.
  • Running the pump dry to test it. Dry running damages the seals and bushings.

For sizing a pump so it doesn’t overwork, see pond pump and filter setup. If the filter is the blockage, see cleaning a pond filter. If the pump has been out for a while, check the oxygen risk in the common causes of fish death in ponds.

The complete guide to pumps and filters

Pond Pump and Filter Setup: Sizing and Plumbing a Pond System
Read the guide

Keep exploring

Guides from other topics

All topics →