Pumps and Filters

What are the most common causes of fish death in ponds?

The most common causes of fish death in ponds are poor water quality, low oxygen, pump or power failure, and disease. Test the water before you treat.

On this page
  1. Poor water quality
  2. Low oxygen
  3. Pump and power failure
  4. New pond syndrome
  5. Overfeeding and cold water
  6. Chlorine, pH and new concrete
  7. Disease and parasites
  8. Predators
  9. Toxins and new fish
  10. What to do if fish start dying

Poor water quality is the top cause of fish deaths in ponds. Low oxygen, a failed pump or power supply, new-pond problems, and disease and parasites are the other main causes. Test the water before you assume disease, and check the pump and oxygen first.

Poor water quality

Test ammonia and nitrite regularly. Both should read zero in an established pond.

  • Ammonia is more toxic at higher pH and temperature. Levels above about 0.5 ppm total ammonia are dangerous.
  • Nitrite starts to stress fish at around 0.25 to 0.5 ppm.
  • pH and hardness. Aim for a pH of about 7.0 to 8.5 and a KH (carbonate hardness) of about 70 to 140 ppm (4 to 8 dKH). Low KH lets pH crash suddenly, which stresses fish.

Low oxygen

Oxygen drops on hot nights, during overcast spells, after an algae die-off, and in overstocked ponds. Fish gasp at the surface, usually around dawn, when levels are lowest.

Aim for oxygen above about 5 to 6 mg/L. Fish are stressed when levels fall below about 5 mg/L. Waterfalls, fountains and aerators help, though a direct-drive solar aerator gives no oxygen at night (see solar pond pumps and aerators).

Pump and power failure

When the pump or its power stops, oxygen drops and the filter bacteria begin to starve, often within hours. The speed depends on the pond’s size, stocking and temperature.

Check the GFCI and the pump first. The pond pump not working guide walks through the checks. In a stocked pond, a battery-backed aerator or a power-failure alarm can give you time to respond.

New pond syndrome

New ponds often lose fish because the fish went in before the biological filter had cycled. The filter needs about 4 to 6 weeks to build up bacteria that convert ammonia to nitrite and then to nitrate. Until then, ammonia and nitrite can build up to toxic levels.

Test regularly during the first weeks, and add fish only once the readings settle at zero for ammonia and nitrite.

Overfeeding and cold water

Overfeeding fouls the water. Uneaten food decays and adds ammonia. Stop feeding below about 50°F (10°C), when fish slow down and digest food poorly. Fish don’t need feeding through winter.

Chlorine, pH and new concrete

  • Tap water contains chlorine or chloramine. Dechlorinate any tap water you add, and keep untreated top-ups to about 10 percent of the pond volume or less.
  • Fresh concrete or mortar leaches lime and pushes pH up. Cure it or seal it fully before you add fish.

Disease and parasites

  • New fish can carry parasites such as white spot (ich), flukes and Costia, and viruses such as KHV and SVC. Quarantine new fish for about 3 to 4 weeks, away from the main pond.
  • Spring is high risk. Parasites become active before fish immunity recovers in water below about 59°F (15°C).
  • Bacterial ulcers from Aeromonas often follow stress or parasite damage.
  • Notifiable diseases. KHV and SVC are notifiable in some countries, including the UK. Report suspected cases to the relevant authority.
  • Don’t add salt or medication without testing. Untested treatments often make things worse.

Predators

Herons, raccoons, otters, mink and cats all hunt pond fish. A deep zone with steep sides and cover in the form of plants or fish caves makes the pond harder to raid. Netting over the pond can help while predators are active. The depth guide for fish ponds covers depth and predator protection in more detail.

Toxins and new fish

Lawn chemicals, runoff, treated timber and copper fittings can all poison fish. Keep chemicals well away from the pond and check the materials you use nearby.

When you add new fish, float the bag on the surface for about 15 to 20 minutes so the water temperature in the bag matches the pond before you release them.

What to do if fish start dying

  1. Test ammonia, nitrite and pH, and check oxygen if you can.
  2. Check the pump, power and aeration.
  3. Look for the common causes above, starting with water quality.
  4. Avoid quick fixes such as untested salt or medication.
  5. If you suspect a notifiable disease or a toxin, contact a local aquatic vet or the relevant authority before doing anything else.

For the wider system that keeps water quality stable, see pond pump and filter setup. For filter care that avoids restarting the bacterial cycle, see cleaning a pond filter.

The complete guide to pumps and filters

Pond Pump and Filter Setup: Sizing and Plumbing a Pond System
Read the guide

Keep exploring

Guides from other topics

All topics →