Clean the mechanical media when the flow drops, which in summer is usually weekly to monthly, depending on fish load and leaf fall. Rinse biological media only when it is blocked, and always in pond water, never tap water. Clean half the filter at a time so the bacteria in the other half survive.
How often to clean
- Mechanical foam and brushes: weekly to monthly in summer. Clean more often in leaf fall or when the fish load is high.
- Biological media: rinse only when the flow drops. That is usually a few times a year at most.
- Bead filters: backwash regularly, often about weekly. The exact interval varies.
- Vortex or multi-chamber filters: purge sludge through the bottom valves, often weekly.
- Japanese matting: hose it down or dunk it in pond water when it clogs. It lasts for years.
- Spring: do the main clean once the water is above about 50°F (10°C).
- Winter: clean lightly, if at all.
Signs the filter needs cleaning
- Return flow from the filter has weakened.
- A gravity (box) filter is overflowing.
- Water runs around the media instead of through it.
What you need
Keep a bucket of pond water for rinsing, a spare bucket for sludge, and a pair of gloves. Don’t use tap water at any stage.
Step by step
- Switch off and unplug the pump and the UV before you open the filter.
- Remove the foam pads, brushes and mats.
- Squeeze or dunk the foams in the bucket of pond water until they are mostly clear. Leave some brown sludge in them. Don’t aim for spotless.
- Rinse biological media only if it is heavily blocked. Swish it gently in pond water, and keep most of the film of bacteria on it.
- Flush the chamber. Spray out the empty box, or drain the sludge from the bottom. If there is a backwash or cleanout valve, run it until the water runs clear.
- Wipe the UV quartz sleeve so algae or scale doesn’t block the light.
- Reassemble the filter in order, usually coarse to fine. Close the lids and valves, turn the pump back on, and check for leaks and steady flow.
Clean in stages
Clean half the filter now, and the rest after about 2 to 4 weeks. The bacteria in the half you leave alone keep the filter working while the other half recovers.
Keep downtime under about an hour where you can. After several hours with the pump off, flush the filter to waste before you restart it, because the media can go anaerobic. Test ammonia and nitrite over the next few days after any big clean.
Pressurized, gravity and bead filters
- Pressurized filters: use the cleaning handle or backwash, and run the dirty water to waste.
- Gravity (box) filters: remove the upper media, clean it, then clear the sludge from the base.
- Bead filters: backwash regularly, following the manufacturer’s schedule.
UV bulbs and sleeves
Replace the UV bulb about every 12 months. A bulb that still lights may have lost most of its UV-C output, so it can look fine while doing very little. Keep the quartz sleeve clean. Never look directly at a lit UV-C lamp.
What not to do
- Don’t use detergent, bleach or a pressure washer on biological media.
- Don’t rinse in tap water. Chlorine and chloramine kill nitrifying bacteria.
- Don’t clean everything to a spotless finish. A spotless filter has lost its bacteria.
- Don’t switch the filter off for days in summer. It isn’t harmless, and the bacteria and oxygen suffer.
Safety
Wear gloves. Pond sludge can carry bacteria such as Mycobacterium marinum, so cover any cuts before you start. Unplug the pump and UV before you open the filter, and keep electrics away from wet hands.
Using the sludge
Filter sludge can make a useful garden fertilizer. Spread it on beds rather than dumping it in the pond.
For sizing the filter in the first place, see pond pump and filter setup. For media order and covers, see pond filter installation. If the flow is low even after cleaning, see pond pump not working.