Draining a pond is a big job, and it isn’t routine maintenance. Most ponds need a full drain-down only every three to five years at most, and only when there is a reason: repairing a liner, removing a thick sludge layer, changing the layout, or filling the pond in. Draining every year doesn’t make a pond healthier. It strips out the established bacteria and stresses the fish and any wildlife.
If you’re draining for a repair or a clean-out, you’ll also want to read about repairing leaks first, so you don’t drain the pond twice.
Check the rules first
- Fish. Releasing pond fish into the wild is illegal in many places, and goldfish are invasive. Keep the fish, or rehome them through a local pond club or a shop that takes them.
- Discharge. Pond water can’t go down every drain. Check your local rules before pumping onto the street or into a storm drain. Pond water often carries nutrients and can carry bacteria.
- Protected wildlife. In the UK, great crested newts are protected, and disturbing them needs a licence. Check for amphibians before you start.
- Timing. Autumn is often the most practical time, when the water is cool. Spring works too, but avoid the amphibian spawning season, which runs from about February to May in many regions, if frogs, toads or newts use the pond.
Work out the pond’s volume
To estimate how much water you’re removing, use this:
- US units: length × width × average depth (in feet) × 7.48 = gallons.
- Metric: length × width × average depth (in metres) × 1,000 = litres.
For example, a pond 4 m long, 3 m wide and 0.8 m deep on average holds about 9,600 litres (4 × 3 × 0.8 × 1,000). A pond 12 ft by 10 ft with an average depth of 2.5 ft holds about 2,240 gallons (12 × 10 × 2.5 × 7.48).
To estimate the drain time, divide the volume by the pump’s flow rate. Pump ratings are usually given with no lift, so the real flow is lower, especially when the pump lifts water up and out. Treat the result as a rough guide.
Choosing a pump
For draining, use a submersible sump pump or a dirty-water pump rated for solids. A trash pump handles silt and debris better than a standard clean-water pump.
Stand the pump on a brick or a stand, so the intake sits just off the bottom and doesn’t pull up silt. Keep the water level above the intake, because a pump that runs dry can overheat and burn out. Check the pump regularly during the job.
The downsides of a pump: it needs a power supply at the pond edge, and that supply should be protected by an RCD or GFCI. Pumps can clog with leaves and sludge, make noise, and run hot. Stay close enough to the job to notice when the water level falls too low for the pump.
Can you siphon with a garden hose?
Yes, a hose can siphon water, provided the outlet end is lower than the pond’s surface and the hose stays full. Start it by filling the hose completely with clean tap water before you place the ends.
Never start a siphon by sucking on the hose. Pond water can carry bacteria, and you should not put it in your mouth. A siphon also stops once the water falls below the inlet end, so it can’t empty the pond fully. You’ll need a pump to finish the job.
Keep the fish and filter alive
- Hold the fish in an aerated tank, shaded and covered, filled with pond water. Keep the tank cool.
- Keep filter media submerged in pond water in the holding tank. Don’t put it in tap water, because chlorine in tap water can kill the bacteria on the media.
- Keep plants wet. Move them to buckets of pond water or a shaded spot, and check them often.
- Acclimatise the fish slowly to any temperature difference when you return them to the pond.
Draining the pond
- Remove the fish and plants as described above.
- Place the pump at the lowest point and run the discharge line to where the water can go.
- Check for frogs, newts and other creatures as the water drops. Move any you find to a holding tank or the pond edge.
- Remove the remaining sludge by hand with a shovel, or with a pond vacuum if you have one. Go slowly and watch your footing.
What to do with the silt
Pond silt is nutrient-rich, and it can be useful. Spread it on beds or compost it before use. If it smells of hydrogen sulphide (rotten eggs), leave it to air for a few weeks first.
Keep silt from road runoff, or from a pond that has been treated with copper, away from edible crops. Pond silt isn’t automatically safe for vegetables. Don’t tip silt into streams or drains.
Clearing a silty pond without draining
If the pond is only silty and not in need of a full drain, you can often manage it without emptying it. Remove sludge in stages, taking out no more than about a third at a time, so the bacteria and the bottom habitat remain. Cut the inputs too: keep leaves out with netting, feed less, and fix any runoff that brings soil in.
Some keepers use gypsum (calcium sulphate) to settle clay silt. Before you use it, do a bucket test: fill two buckets with pond water, add a little gypsum to one, and watch both for a week. Some sources say the treated water clears within days, but it depends on the cause. Gypsum won’t fix silt that keeps arriving from erosion or runoff, so address the source. Follow the product label for any amount.
Refilling the pond
Refill with dechlorinated water. Rainwater is a good choice if you have it. Put the fish back slowly, and acclimatise them to the new temperature first. Restart the filter with pond water in the media.
After refilling, test for ammonia and nitrite spikes, and feed lightly for one to two weeks while the bacteria recover.
Filling in the pond to make a garden
If you want to turn the pond into a garden bed or border, the steps are:
- Remove the fish and plants, and take out as much sludge as you can.
- Remove the liner. If you leave it in place, puncture it thoroughly in many places so water can’t pool.
- Backfill the hole with rubble or subsoil, then add 15 to 30 cm (6 to 12 in) of topsoil.
- Overfill slightly. Soil settles, so allow for about 10 to 20% extra; the exact amount varies with the soil.
- Consider a bog garden instead. Puncture the liner and fill the pond with soil and peat-free compost, then plant moisture-loving plants.
Check for buried pipes and cables before you dig, and be careful with the liner, which can be sharp.
Safety
Use an RCD or GFCI on every pump and cable, and keep cables off wet ground. Wear gloves when handling sludge, because it can carry bacteria, and cover any cuts. Take care on slippery edges and in soft silt. Don’t go into a deep pond or a sludge pit alone.